top of page

Why Do Ball Bearings Reduce Friction? Rolling vs Sliding Friction Explained

11 minutes ago
4 min read
Why Do Ball Bearings Reduce Friction? Rolling vs Sliding Friction Explained
Why Do Ball Bearings Reduce Friction? Rolling vs Sliding Friction Explained

Almost everything that spins, from a skateboard wheel to a jet engine, rides on bearings. The reason is simple: rolling is far easier than sliding.

The animation below puts two identical shafts side by side with the same motor, load and flywheel. One turns in a plain bronze bushing and the other in a ball bearing. At 10 seconds both motors switch off. You can change the load and the friction of the bushing and compare speed, heat and coast-down.

The short answer

In a plain bushing, the shaft slides against the bushing, and the whole surface scrapes. In a ball bearing, the shaft rides on steel balls that roll: a rolling ball just lifts away from its contact point instead of dragging across it. The friction coefficient of rolling is dramatically smaller. The animation uses μ of about 0.0015 for the ball bearing and 0.12 for the dry bushing, a ratio of about 80 to 1.

With the default 2,000 N load the model gives, for the same motor: the bushing reaches only about 690 rpm and wastes about 217 W as heat, while the ball bearing reaches about 2,733 rpm and loses only about 10.7 W.

What the animation shows, stage by stage

  1. Same motor, same load. On the left the shaft slides inside a bronze bushing. On the right it rides on a ring of steel balls.

  2. Sliding vs rolling. Sliding surfaces scrape across each other. A rolling ball just lifts off its contact point, like a wheel.

  3. Where the power goes. The bushing turns motor power into heat and the motor can only reach a low speed. The bearing loses very little.

  4. Motors off. The bushing shaft stops in about a second. The bearing shaft keeps spinning on its stored energy.

  5. The answer. Rolling friction is about 80 times smaller than sliding friction in this model.

The physics: friction torque and wasted power

Friction force is the friction coefficient times the load, F = μ · N. At a shaft, that force acts at the contact radius and makes a friction torque that the motor has to overcome. The power lost as heat is the friction torque times the angular speed.

The motor in the model has a limited torque. With a high friction coefficient or a high load, the friction torque eats most of the motor torque, so the shaft cannot reach a high speed. And once the motor is off, the only thing that slows the flywheel is friction, so the coast-down time is a direct measure of it.

What the numbers say: load and sliding friction

The ball bearing runs at about 2,700 rpm in every case, since its friction is tiny. For the bushing, the model gives:

Load

Bushing speed

Bushing coast-down

Ball bearing heat

500 N

2,242 rpm

10.0 s

2.7 W

2,000 N (default)

690 rpm

1.2 s

10.7 W

4,000 N

stalls (0 rpm)

none

21.3 W

And with the default load, changing the friction coefficient of the bushing:

Bushing μ

Bushing speed

Coast-down

0.05

1,897 rpm

7.9 s

0.12

690 rpm

1.2 s

0.15

172 rpm

0.2 s

0.25

stalls (0 rpm)

none

Note that at the highest load or friction the bushing shows no speed and no heat at all. That is not good news: the motor is stalled because the friction torque is larger than the motor can supply.

Honest limits of the model

The model uses fixed friction coefficients and a motor with a simple torque limit. It does not model lubrication, which in a real bushing can lower the friction a lot, nor the contact stresses, speed limits or life of a real ball bearing. A lubricated plain bearing can be very good. The animation compares a dry bushing with a ball bearing to make the principle clear.

Frequently asked questions

Why is rolling friction so much lower than sliding friction? A rolling element does not drag across the surface. It lifts off its contact point as it rolls, so almost no sliding happens and far less energy is lost.

Where does the lost power go? It becomes heat. In the model the bushing wastes about 217 W as heat at the default settings, and its temperature rises far more than the bearing's.

What happens when the friction is too high for the motor? The motor stalls. In the model a 4,000 N load, or a friction coefficient of 0.25, stops the bushing shaft completely.

Why does the bearing shaft coast for so long after power-off? Only a very small friction torque slows it, so its stored kinetic energy lasts a long time.

Do ball bearings have any friction at all? Yes, but it is small. The model uses a coefficient of about 0.0015.

Does lubrication change the comparison? Yes. A lubricated plain bearing has far lower friction than a dry one. The animation compares a dry bushing with a ball bearing for simplicity.

Related

Figures in this article come from the animation's simplified model: a dry bronze bushing with μ of 0.05 to 0.25 (0.12 default) against a ball bearing with μ of about 0.0015, loads from 500 to 4,000 N (2,000 N default), and motors switched off at 10 s. They illustrate the principle and are not bearing-design data.

Comments


bottom of page