How Can a Small Motor Lift a 400-Tonne Bridge? The Bascule Counterweight Explained

A bascule bridge lifts a leaf of hundreds of tonnes so a ship can pass, and the motors that do it are surprisingly small. The reason is that the bridge is a balanced seesaw.
The animation below opens a 400-tonne leaf with a 1,200-tonne counterweight on the short arm behind the pivot. You can change the counterweight and the opening angle, and watch the leaf moment, the counterweight moment and the motor torque.
The short answer
The leaf's weight acts 11.66 m from the pivot (the trunnion), while the 1,200 t counterweight sits 3.89 m on the other side. The turning moments are almost equal: 400 × 11.66 ≈ 1,200 × 3.89. As the leaf tips up, both lever arms shrink by the same factor, cos θ, so the moments stay balanced at every angle. The motor only has to overcome friction, wind and the small leftover imbalance.
In the animation's model each side has a moment of about 45,750 kN·m when the bridge is closed, and the motor torque is only about 39 kN·m of imbalance plus an illustrative 120 kN·m of friction.
What the animation shows
The leaf pivots on a trunnion near the shore. On the short arm behind the pivot there is a very heavy counterweight. The animation shows the moment of each side, the angle and the motor torque during the opening and closing. A boat passes under the open leaf.
The physics: moments about the pivot
The turning effect of a weight about a pivot is its weight times its horizontal distance from the pivot. For the leaf and the counterweight in the model:
Leaf moment = 400 t · g · 11.66 m · cos θ
Counterweight moment = W · g · 3.89 m · cos θ
The cos θ factor is common to both, so if they balance when the leaf is flat they balance at every angle. That is the whole trick: the bridge is neutrally balanced, and lifting it takes almost no work against gravity. The motor torque is the imbalance plus friction.
What the numbers say: what if the counterweight is off?
The counterweight in the model is 800 to 1,600 t. At the default 1,200 t the imbalance is tiny. Moving 400 t either way changes everything:
Counterweight | Motor torque needed (from 75° to 0°) |
800 t | 3,820 to 15,345 kN·m |
1,200 t (default) | 10 to 159 kN·m |
1,600 t | 3,841 to 15,424 kN·m |
A counterweight that is 400 t too light or too heavy needs about 100 times more motor torque at the worst angle. The bridge is balanced by design and carefully checked, because the motor is sized only for friction and wind.
The opening angle changes where the leaf stops. At 50° the leaf moment is still about 29,400 kN·m, while at 80° it is only about 7,900 kN·m, since cos θ shrinks. The balance holds at every angle.
Honest limits of the model
The friction value of 120 kN·m is illustrative, and the model ignores wind, inertia while accelerating, the rolling or sliding of real counterweights, and the safety margins of a real design. Real bascule bridges are usually set slightly out of balance on purpose, so that the drive and brakes always hold the leaf positively.
Frequently asked questions
What is a bascule bridge? A drawbridge whose leaf pivots about a horizontal axis, tipping up like a seesaw, with a counterweight balancing the leaf.
Why does the motor not need to be large? Because the counterweight balances the leaf, so the motor does not lift the weight. It only overcomes friction, wind and a small imbalance.
Why does the balance hold at every angle? Both lever arms shrink by the same factor, cos θ, so the ratio of the moments never changes.
What happens if the counterweight is too light? The leaf is heavier than the counterweight and the motor must hold it up. In the model 800 t needs about 100 times more torque at the worst angle.
What is the trunnion? The pivot shaft on which the bridge leaf turns.
Is the counterweight really three times the leaf? In this model, yes: 1,200 t against 400 t, because it sits at about a third of the distance from the pivot.
Related
Figures in this article come from the animation's model: a 400 t leaf with its centre of weight 11.66 m from the trunnion, a counterweight of 800 to 1,600 t (1,200 t default) at 3.89 m, an opening angle of 50° to 80° (75° default), and an illustrative friction torque of 120 kN·m.




Comments