Nozzle Mechanism Explained: How One Cam Opens and Closes Two Nozzle Halves

Some nozzles have to change their opening on demand. A simple way to build one is to make it from two halves that slide apart or together. The hard part is to move both halves by the same amount, in opposite directions, from one motor. A cam does exactly that.
The interactive lab from 3D Mechanism shows such a nozzle mechanism, from the pinion that the motor turns to the two nozzle halves. Its big idea in one line: turn the cam back, and the halves close again. The model and its motion come straight from the CAD file.
What Is This Nozzle Mechanism?
It is a drive made of gears, a cam and two follower pins. A small pinion turns a larger gear that carries a cam, the cam moves two pins in opposite directions, and each pin moves one half of the nozzle. The parts, in the order the motion travels:
Pinion ×2 → cam → driven gear → follower pin ×2 → nozzle half ×2
Pinion (two): the small input gears, turned by the motor.
Driven gear: a bigger gear that the pinion turns.
Cam: a plate with a curved edge, mounted on the driven gear.
Follower pins (two): pins that ride on the cam's curve.
Nozzle halves (two): each one is moved by one of the pins.
How It Works, Step by Step
The lab has five steps:
Pinion. It starts at a small pinion, turned by the motor.
Cam gear. The pinion turns a bigger gear with a cam on it, about 92 degrees in the model.
Followers. Two pins ride on the cam's curve, and slide in opposite directions.
Nozzle halves. Each pin moves one half of the nozzle, about 4.5 mm.
All together. Every part moves at once.
What a Cam and Follower Does
A cam is a part whose edge is not round, so its distance from the center changes as it turns. A follower that rides on that edge is pushed in and out as the cam turns. The shape of the curve decides exactly how the follower moves: how far, how fast and in which direction. That is why a cam is such a convenient way to produce a precisely controlled movement from a plain rotation.
In this mechanism, the two followers ride on the cam's curve at opposite sides, so when one is pushed one way the other moves the opposite way. Each pin is attached to one half of the nozzle. The result is that both halves move the same distance, in opposite directions, so the opening between them grows or shrinks evenly and stays centered.
Why Use Gears Before the Cam?
The motor turns a small pinion, and the pinion turns a bigger gear with the cam on it. A gear stage like this changes the speed and the turning force between the motor and the cam, and it gives a convenient way to place the cam where the nozzle needs it. The lab does not state the number of teeth or the gear ratio, so this article does not give one either.
Why the Motion Can Be Reversed
The lab plays the motion forward and then back (ping-pong). Its big idea says it all: turn the cam back, and the halves close again. A cam and follower drive is a positive, geometric connection, so reversing the cam reverses the followers along the same path. This makes the opening easy to control: how far you turn the cam decides how far the halves move.
Reading the Numbers in the Lab
The lab shows numbers measured on the 3D model while it moves:
Pinion: 93° of turn in the model's motion.
Nozzle half: 4.4 mm of travel.
Cam gear: about 92°. That is the number given in step 2.
The live panel shows the pinion's turn in degrees and the nozzle half's travel in millimeters as the model plays, and the technical view draws the parts on a diagram that you can switch between front, back, left, right and top. The lab plays at half speed. These are measurements of this CAD model, not ratings for a real nozzle.
What to Try in the Lab
Go through the five steps and watch which parts light up.
Use Auto to play the sequence, or Manual and press Space for the next step.
Watch the two nozzle halves move apart and then back together as the cam turns.
Look at the follower pins on the cam's edge, and see that they move in opposite directions.
Turn on X-ray to see through the housing, and CAD colours to tell the parts apart.
Use the Front and Top views to compare the movements of the two halves.
Where This Kind of Mechanism Is Used
A cam that moves two parts in opposite directions is useful whenever an opening or a gap has to be adjusted evenly:
Adjustable nozzles and apertures where two halves open and close.
Machines that need a symmetric opening, such as dispensers or feeders.
Test rigs and demonstration models that show how a cam sets a movement.
The lab does not name a specific product, so treat these as typical uses of the idea, not as claims about this model.
Designing a Cam and Follower Nozzle in CAD
These are general design points, not specifications from this model:
Start from the movement you need. Decide how far each half has to move (about 4.5 mm in this model) and how the opening should change with the turn.
Draw the cam's curve from that movement. The shape of the cam is the shape of the motion.
Place the followers symmetrically. Opposite positions make the two halves move in opposite directions by equal amounts.
Keep the followers in contact. A spring, a groove or a second cam surface stops the pins from losing the curve.
Run a motion study. Check the full range, and check that no part collides when the halves are fully open or fully closed.
Designing for 3D Printing
A printed cam nozzle is a good teaching model.
Print the cam and gears flat, so the layers run along the tooth faces.
Use a smooth cam surface, because printed surfaces are rough and the followers will wear it.
Leave clearance for the sliding nozzle halves, and test the fit.
Add backlash to the gears so they do not bind.
Common Problems
The followers jump off the cam: nothing holds them against the curve. Add a spring or a guiding groove.
The two halves do not move equally: the followers are not placed symmetrically, or one has more play.
The cam wears quickly: the contact is too small, or the surfaces are too rough.
The gears grind: the center distance is wrong, or there is too little backlash.
Frequently Asked Questions
How does a cam and follower nozzle mechanism work? A motor turns a pinion, which turns a bigger gear with a cam. Two follower pins ride on the cam's curve and slide in opposite directions, and each one moves one half of the nozzle.
Why do the nozzle halves move in opposite directions? The two followers ride on opposite sides of the cam's curve, so when the cam pushes one pin one way it moves the other the opposite way.
How far do the nozzle halves move in the lab? About 4.5 mm each in the CAD model.
Why can the halves close again? A cam and follower drive is a direct geometric connection, so turning the cam back moves the followers back along the same path.
Are the lab numbers real specifications? No. They are measured on the model while it moves and describe this model only.




Comments