top of page

Bend allowance: Formula, Calculator and Worked Example

5 hours ago
3 min read
Bend allowance: Formula, Calculator and Worked Example
Bend allowance: Formula, Calculator and Worked Example

Bend allowance is the length of the neutral axis through the bend. It is used to calculate the flat pattern of a formed part.

Bend allowance is the length of the neutral axis through a bend. Because the inside of the bend compresses and the outside stretches, only the neutral axis keeps its original length, and that is the length you must add to the straight segments to get the flat pattern.

Where bend allowance matters

Every sheet metal flat pattern depends on bend allowance or its companion values, bend deduction and outside setback. CAD programs use the same relationships internally, driven by a K-factor or a bend table.

In sheet metal design, small geometric decisions such as radii, reliefs and hole positions decide whether a part can be cut and bent reliably on standard press brakes, and they have a direct effect on cost, flatness and repeatability.

Formula

BA = π·θ·(R + K·t) / 180 • OSSB = tan(θ/2)·(R + t) • BD = 2·OSSB − BA

The calculation uses the following inputs:

  • Inside radius [mm], accepted range 0.2 to 50 mm

  • Thickness [mm], accepted range 0.3 to 20 mm

  • Bend angle [°], accepted range 1 to 180 °

  • K-factor, accepted range 0.25 to 0.5

It returns:

  • Bend allowance (BA) [mm]

  • Neutral-axis radius [mm]

  • Outside setback (OSSB) [mm]

  • Bend deduction (BD) [mm]

Assumptions: θ is the angle swept from flat. The K-factor depends on material, tooling and R/t (typically 0.33 to 0.5).

Worked example

Take the following values, which are also the default settings of the calculator:

  • Inside radius: 3 mm

  • Thickness: 2 mm

  • Bend angle: 90 °

  • K-factor: 0.4

Applying the formula gives:

  • Bend allowance (BA): 5.969 mm

  • Neutral-axis radius: 3.8 mm

  • Outside setback (OSSB): 5 mm

  • Bend deduction (BD): 4.031 mm

With these values no design warning is triggered, so the result sits inside the usual practical limits. Change one input at a time in the calculator to see how sensitive the result is; the response curve shows how the main result varies across the full range of the first input.

Sensitivity: which input matters most?

Starting from the worked example, each input below was changed by 20 percent while the others were held constant. The table shows the effect on bend allowance (ba) (baseline 5.969 mm).

The most influential input here is bend angle, which moves the result by up to 20 percent for a 20 percent change, while k-factor has the smallest effect (4.2 percent). Focus measurement accuracy and design margin on the inputs at the top of the table.

How to use the calculator

  1. Choose metric or US customary units with the toggle at the top. Inputs and results convert automatically.

  2. Enter inside radius, thickness, bend angle and the remaining inputs with the sliders or by typing values.

  3. Read the main result, bend allowance (ba), together with the secondary results and any warning shown below it.

  4. Check the schematic: it redraws with your values so you can confirm the geometry and dimensions make sense.

Design tips

  • Calibrate the K-factor from a test bend on your own press brake, material and tooling; published values are only a starting point.

  • Keep one K-factor per material, thickness and die combination in your CAD library so flat patterns stay consistent across parts.

  • Remember that the angle used in the formula is the angle swept from flat, not the included angle between flanges.

Frequently asked questions

What is a typical K-factor?

For air bending, values between 0.33 and 0.5 are common. Small radii relative to thickness give lower values; generous radii move the neutral axis toward mid-thickness and K approaches 0.5.

What is the difference between bend allowance and bend deduction?

Bend allowance is added to the flat lengths measured to the bend tangents. Bend deduction is subtracted from the sum of flange lengths measured to the outside mold lines. Both describe the same geometry.

Which units does the bend allowance calculator use?

Inputs are entered in mm, ° in metric mode. Switching to US customary units converts lengths to inches, forces to pound-force, stresses to psi and masses to pounds where applicable, and all results are converted the same way.

Related sheet metal tools

The formulas and reference values on this page are intended for education and preliminary design. Always verify critical parts against the applicable standards, supplier data and, where required, a qualified engineer.

Comments


bottom of page