top of page

ISO Metric Bolt Torque, Preload & Tap Drill Calculator

10 minutes ago
5 min read
ISO Metric Bolt Torque, Preload & Tap Drill Calculator
ISO Metric Bolt Torque, Preload & Tap Drill Calculator

The tightening torque for an ISO metric bolt comes from one short equation: T = K · Fᵢ · d. Here Fᵢ is the clamp force (preload) you want in the joint, d is the nominal diameter and K is the nut factor, which lumps together thread and under-head friction. A dry M8 class 8.8 bolt loaded to 75% of its proof load needs roughly 25 Nm. The same bolt lubricated needs only about 18 Nm to reach the same clamp force.

This calculator pulls the ISO 261 coarse pitch, the ISO 898-1 tensile stress area and the proof strength of the selected property class, then returns the torque, preload, proof load, tap drill, clearance hole and wrench size in one view. Use it to fill in the torque note on a drawing, choose a tap drill for a tapped hole in CAD, or check whether a smaller bolt grade would still hold the joint closed.

How do you use the ISO metric bolt torque calculator?

  1. Choose metric (mm, Nm, kN) or imperial (in, lb-ft, lbf) output with the toggle at the top.

  2. Pick the thread size, from M3 × 0.5 to M36 × 4.0. All sizes use the ISO coarse pitch.

  3. Select the property class: 4.6, 5.8, 8.8, 10.9, 12.9 or stainless A2-70. The yield strength appears next to the selector.

  4. Set the surface condition: dry steel (K = 0.20), zinc plated (K = 0.18) or lubricated (K = 0.14).

  5. Adjust the preload utilization between 50% and 90% of proof load. 75% is the usual target for reusable joints.

  6. Read the torque, clamp force, tap drill and stress area in the result cards. Click a row in the reference table to load another size.

What are the formulas behind the ISO metric bolt torque calculation?

Four relations drive the calculation:

Aₛ = (π/4) · (d − 0.9382·P)²          tensile stress area (ISO 898-1)
F_proof = Sₚ · Aₛ                     proof load
Fᵢ = utilization · Sₚ · Aₛ            target preload
T = K · Fᵢ · d                        tightening torque (short form)

Sₚ is the proof strength of the property class (580 MPa for 8.8, 830 MPa for 10.9, 970 MPa for 12.9), P is the pitch and d is the nominal diameter in meters when torque is in Nm. The tap drill follows the shop rule D_drill ≈ d − P, which gives about 75% thread engagement. The external-thread minor diameter is d₃ = d − 1.22687·P.

Why does K matter so much?

Only about 10–15% of the applied torque stretches the bolt. The rest is lost to friction under the head and in the threads. K captures that friction, so a change from 0.20 to 0.14 changes the torque for the same preload by 30%. Always state the lubrication condition next to a torque value on a drawing.

Worked example: step by step

Take the default joint: M8 × 1.25, class 8.8, dry steel, 75% utilization.

  1. Stress area: Aₛ = (π/4)·(8 − 0.9382·1.25)² = 36.6 mm².

  2. Proof load: F_proof = 580 MPa × 36.6 mm² = 21,230 N = 21.23 kN.

  3. Preload: Fᵢ = 0.75 × 21.23 = 15.92 kN.

  4. Torque: T = 0.20 × 15,920 N × 0.008 m = 25.5 Nm (18.8 lb-ft).

  5. Tap drill: 8 − 1.25 = 6.8 mm. The medium clearance hole is 9.0 mm and the hex needs a 13 mm wrench.

If the same bolt is lubricated (K = 0.14), the torque for the same 15.92 kN preload drops to about 17.8 Nm. Applying the dry value of 25.5 Nm to a lubricated bolt would push it past its proof load.

Quick reference table

Preload and torque below assume class 8.8 at 75% of proof load. The last column shows the lubricated torque for comparison.

ISO metric coarse bolts: tap drill, stress area, preload and torque (class 8.8, 75% proof)

Size

Pitch (mm)

Tap drill (mm)

Aₛ (mm²)

Preload (kN)

Torque dry K=0.20 (Nm)

Torque lubed K=0.14 (Nm)

M5

0.8

4.2

14.2

6.18

6.2

4.3

M6

1.0

5.0

20.1

8.74

10.5

7.3

M8

1.25

6.8

36.6

15.9

25.5

17.8

M10

1.5

8.5

58.0

25.2

50.5

35.3

M12

1.75

10.2

84.3

36.7

88.0

61.6

M16

2.0

14.0

157

68.3

219

153

M20

2.5

17.5

245

107

426

298

M24

3.0

21.0

353

154

737

516

Design and CAD tips: tolerances and common mistakes

  • Model the tap drill, not the major diameter. In CAD, a tapped M8 hole is a 6.8 mm drilled hole with a cosmetic thread. Add about 1.5 × P of extra drill depth beyond the full thread so the tap does not bottom out.

  • Thread engagement. In steel, 1 × d of engagement is enough for a class 8.8 bolt. In aluminum or cast iron use 1.5–2 × d, or fit a helical insert, so the internal thread does not strip before the bolt yields.

  • Clearance holes. ISO 273 gives fine, medium and coarse series. The medium series (9.0 mm for M8) suits most bolted plates. Use the fine series when bolts also locate parts.

  • Torque scatter. A click-type torque wrench gives ±25% preload scatter because friction varies. For critical joints, specify torque-angle tightening or direct tension indicators.

  • Common mistake: copying a torque table without checking its K value and preload percentage. Two tables for the same bolt can differ by 40% for that reason alone.

Frequently asked questions

What torque should I use for an M8 8.8 bolt?

About 25 Nm dry or 18 Nm lubricated for a preload of 75% of proof load (about 15.9 kN). Use the lower value whenever threads are oiled, waxed or coated with anti-seize.

What size drill do I need to tap an M8 thread?

A 6.8 mm drill, from the rule nominal diameter minus pitch (8 − 1.25). The same rule gives 5.0 mm for M6, 8.5 mm for M10 and 10.2 mm for M12.

What does the K factor mean in bolt torque?

K is the nut factor. It is an empirical coefficient that combines thread friction, under-head friction and thread geometry. It typically ranges from 0.10 for well-lubricated threads to 0.20 for dry steel and up to 0.30 for rusty or plain stainless threads.

Why preload a bolt to 75% of proof load?

High preload keeps the joint clamped under external load, so the bolt sees only a small fraction of the fluctuating force. That greatly improves fatigue life and resistance to loosening, while 75% still leaves margin for torque scatter.

The formulas and reference values on this page are intended for education and preliminary design. Verify critical parts against the applicable standards, supplier data and, where required, a qualified engineer.

Comments


bottom of page