top of page

Cam and Follower Calculator: Lift, Pressure Angle and Undercut Check

3 hours ago
3 min read
Cam and Follower Calculator: Lift, Pressure Angle and Undercut Check
Cam and Follower Calculator: Lift, Pressure Angle and Undercut Check

Define lift, rise, dwell and return angles for a disc cam with a radial roller follower and see velocity, acceleration, pressure angle, undercut risk, timing and follower forces.

What it is

A disc cam turns a rotating motion into a programmed linear motion of a follower. The cam profile is cut from a motion law: the follower rises, dwells at the top, returns and dwells again. This calculator builds that law with a harmonic or a cycloidal curve and then does the checks that decide whether the cam will actually work.

The two key checks are the pressure angle (the angle between the follower's direction of travel and the contact normal) and the radius of curvature of the pitch curve compared with the roller radius. A large pressure angle loads the follower guide sideways. A pitch-curve radius smaller than the roller causes an undercut, so the real cam surface cannot be machined or printed as designed.

The equations used

  • Prime circle radius: Rp = Rb + Rr (base radius plus roller radius)

  • Harmonic rise: s = (h/2)(1 − cos πu), with u = θ / β

  • Cycloidal rise: s = h (u − sin 2πu / 2π)

  • Pressure angle (radial follower): tan φ = (ds/dθ) / (Rp + s)

  • Pitch curve radius of curvature: ρ = (r² + r′²)^(3/2) / (r² + 2r′² − r·r″), with r = Rp + s

  • Low dwell = 360° − rise − high dwell − return

  • Peak contact force: Fn = F / cos φmax; side force on the follower guide: Fs = F tan φmax

Worked example

20 mm lift, 90° rise, 60° dwell, 90° return, 35 mm base radius, 6 mm roller, 60 rpm, 50 N load, harmonic

The prime radius is 35 + 6 = 41 mm and the low dwell is 120°. The peak pressure angle is 21.8° and the smallest radius of curvature on the pitch curve is 36.8 mm, larger than the 6 mm roller, so the profile does not undercut. At 60 rpm the peak velocity is 126 mm/s and the peak acceleration is 1,579 mm/s². The rise takes 0.25 s. With a 50 N follower load, the peak contact force is 53.9 N and the guide takes a side force of up to 20 N.

Design notes

  • A bigger base circle lowers the pressure angle. If the pressure angle is too high, increase the base radius or spread the same lift over a larger rise angle.

  • Cycloidal motion has no acceleration jump at the start and end of the rise. Harmonic motion has a lower peak velocity but an acceleration step where it meets a dwell.

  • If the undercut check fails, use a smaller roller, a larger base circle or a gentler rise.

  • For 3D printing, print the cam with layers parallel to the rolling direction, and use a bearing as the roller rather than a printed pin.

Frequently asked questions

What is a good pressure angle for a cam? A common guideline for roller followers is to keep the peak pressure angle at or below about 30°. Higher values increase side load and friction on the follower guide.

What causes cam undercut? Undercut happens when the radius of curvature of the pitch curve becomes smaller than the follower roller radius. The offset surface then forms a cusp and the real profile cannot follow the designed motion.

Harmonic or cycloidal motion? Cycloidal gives smoother acceleration with no step at the ends of the rise, at the cost of a higher peak velocity and peak acceleration for the same lift and angle. Harmonic is simpler and common for low-speed cams.

Related

Assumptions: radial (zero-offset) translating roller follower, rigid parts, constant cam speed, no friction. Dynamic effects such as follower jump are not modelled.

Comments


bottom of page